- Bottom line: busk the set that stretches, programme the set that's timed
- The pick for a band that never plays a song the same way twice
- The pick for a show timed to a click track
- The pick for a DJ who runs the lights from the booth
- The pick when nobody is free to run the desk
- The pick when lights and video run from one machine
- The pick for a touring rig with its own programmer
- Concert lighting controllers to shortlist
- An hour at rehearsal that settles it
- What the bill depends on
- Before the first gig on new software
Concert lighting control software should match how your set runs: a busking layout of faders and buttons for a band that stretches its solos, and a programmed cue stack for a show timed to the second. DJs, unattended rigs and lights-plus-video shows each want a different kind of tool again.
Bottom line: busk the set that stretches, programme the set that's timed
Concert lighting has one question under all the others: does the person at the desk follow the band, or does the band follow the show? When a guitarist can turn an eight-bar solo into a two-minute one on a good night, I'd put the money into a busking layout, where every look sits under a fader or a button and the operator plays along. When the set runs to a click or a backing track and the drop lands at the same second every night, a programmed cue stack is the one to trial.
That's the verdict for most acts, and it's the first thing to settle before you open a single download page. The rest of this page gives the pick for each kind of live act, then the controllers themselves, then a rehearsal test that settles it in an hour.
The pick for a band that never plays a song the same way twice
Here the lighting operator is part of the band. They're watching the drummer for the stop, reading the singer for the last chorus, and reaching for a flash button on the hit. What they need is speed of hand, not a long list of programmed cues. A virtual console with big on-screen faders works, but I'd always rather see physical controls, because nobody hits a mouse target in the dark while counting bars.
So the thing to test is mapping: can you put your colour palettes, a strobe, a blackout and a few chase speeds onto a hardware surface and leave the screen alone? On a Mac, Lightkey is one example built to connect a lighting setup to the physical controls on a MIDI controller or DMX console. Whatever you trial, check that a tap-tempo or a rate fader exists for chases, since a band that speeds up will leave a fixed-speed chase behind by the second verse.
The pick for a show timed to a click track
A set that runs to a click is a different job. The looks can be built in the week before the tour, each song becomes a list of cues, and the operator's role shifts from playing to triggering and watching. What matters most here is how much of the programming you can do away from the venue, because desk time in a rehearsal room is short and expensive.
ETC's Eos software is one example: ETC offers it to download so a programmer can work on a show file wherever they go. Before you commit to any cue-based tool, check three things for yourself: whether it can follow timecode or MIDI from the playback rig, how it shows which cue is live and which is next, and how quickly you can edit a cue mid-rehearsal without breaking the ones after it.
The pick for a DJ who runs the lights from the booth
A DJ has no spare hands and no lighting operator. The lights have to come from the same setup that's playing the music, or they won't change at all. That points to software that talks to DJ gear directly rather than a stand-alone console. SoundSwitch is the clear example on this list, working with DJ hardware and software to control DMX lighting as part of the performance.
The check here is compatibility, and it's quick. Confirm that your exact controller and your exact DJ software are named on the maker's site, then load a few tracks from your own library and see how much prep each one needs before the lights behave.
The pick when nobody is free to run the desk
Plenty of gigs have no lighting person at all: a pub residency, a support slot, a self-produced tour in a van. For those, interactive software that reacts to the music is the pick, because it keeps the rig moving without a hand on it. Lightjams is one example, where a live music, video or MIDI signal can drive changes to a DMX lighting show.
Test reactive tools with your real mix at gig volume, not a track on headphones. Listen for how the lights behave in the quiet song and the loud one, since a rig that flickers through a ballad is worse than a static wash. Then check whether you can lock a few fixed looks for the intro and the encore, so the moments that matter aren't left to chance.
The pick when lights and video run from one machine
Acts with an LED wall, a projector or pixel strips on the riser often want lighting and video in one place. There are two routes on this list: console software that bundles a visualiser and media playback, and visual show software that adds DMX control to projection mapping. I'd pick by which side of the show is bigger. When the video carries the night, start on the mapping side; when the lights do, start on the console side.
Either way, test it on the computer that'll sit at front of house. Run the visualiser, the video and a busy chase together for a full song and watch for stutter. It's far cheaper to find that in rehearsal than in the second song of the headline set.
The pick for a touring rig with its own programmer
Once a production carries its own lighting designer and programmer, the software choice tends to follow the console the crew wants to tour with. The controllers to look at are platforms that run on a PC and on dedicated hardware consoles, so the show file built on a laptop in the hotel opens on the desk at the venue.
The design work that comes before this, drawing the rig and picking fixtures, is its own job; there's a separate guide to lighting design software for that stage. For control, check that the show file moves cleanly between laptop and console, and that a spare laptop can take over if the desk fails mid-show.
Concert lighting controllers to shortlist
Lightjams
Interactive DMX software in which live music, video or a MIDI signal drives the changes in a lighting show.
MagicQ
Console software from ChamSys that joins lighting control with full visualisation, pixel mapping and HD media playback, running on Windows, Mac and Linux.
Lightkey
A Mac lighting controller that maps each control on a MIDI controller or DMX console to your on-screen lighting setup.
Want AI doing the heavy lifting in your marketing?
I build the systems that handle the boring 80 percent, so you get your week back. Done properly, with the human kept in.
QLC+
Run as a virtual lighting console on Windows, MacOS or Linux, it controls DMX or analogue lighting systems.
SoundSwitch
Lighting control for DJs: desktop software that works with DJ hardware and software to run DMX lighting as part of the set.
Daslight 5
Desktop DMX lighting software for controlling a rig from a PC or a Mac.
ONYX
Obsidian's lighting control platform, made for industrial hardware consoles and PC systems, with touring productions among the shows it runs.
ETC Eos
ETC's lighting control system, with downloadable software for working on a show file away from the lighting desk.
MadMapper
Visual show software that handles DMX lighting and LED work alongside projection mapping for live visual shows.
An hour at rehearsal that settles it
Don't decide from a feature list. Book an hour with the band and the rig you'll really use, and pick two songs: the one that changes length every night and the one that never does.
For the stretchy song, build four looks (a verse wash, a chorus colour, a solo special and a blackout) and put them on hardware controls. Run the song twice and see whether the operator can follow the band without looking at the screen. For the timed song, programme it as a cue list and run it against the backing track or click. Time how long each build takes; the controller that gets you to a usable song fastest is the one that'll survive a tour.
Then do the unglamorous checks. Save, close and reopen the show file. Pull the USB cable to the DMX interface mid-song and see what the fixtures do and how fast the software reconnects. Ten minutes of that tells you more about a gig night than an afternoon of tutorials.
What the bill depends on
Open-source software, free downloads, free plans and free trials all appear among the makers here, and a free route to programming won't always mean free control of a live rig.
What changes the total is the kit around the software as much as the software itself. Check whether live output needs a hardware key, a specific DMX interface or a branded control surface, how many DMX universes the version you're buying will drive, and whether a second licence is needed for a backup laptop. Those answers shape the bill more than the headline figure.
Do you make lighting control software for live shows? Tool makers can ask to be considered for a featured place on this list.
Before the first gig on new software
Get the show file onto two machines and a memory stick before you leave for the venue. Request the venue's fixture list and DMX patch early, since loading someone else's rig on the night is where a busked show falls apart fastest. And keep the running order, door times and crew contacts somewhere the whole team can see; that side of the night sits better in one of the event apps built for running a show than in a lighting file.
My own call, for a band starting out: begin with a busking layout on hardware you can touch, and only move to a full cue stack when the set stops changing. The lights should feel like another instrument, and that only happens when the operator can play them.
Want your tool on this list? Featured spots and reviews here are paid partnerships. Here's how to partner with me.


